Bare Overhead Conductor

AAC Conductor for Overhead Distribution Lines

AAC проводник, also called all aluminum conductor or AAC cable, is a bare concentric-stranded conductor made from aluminum wires without a steel core. It combines high conductivity with low conductor mass for overhead circuits where the required mechanical loading is moderate.

МатериалAluminum 1350-H19

СтроителствоConcentric stranded

СтандартиASTM B231 / IEC 61089

Primary useOverhead line systems

AAC conductor made from concentric stranded aluminum wires
AAC conductor uses concentric-stranded aluminum wires without a steel core.

XWA AAC Conductor

AAC combines high electrical conductivity with low conductor mass. It is primarily used where span and mechanical loading remain within the capability of an all-aluminum construction.

The finished conductor is configured by governing standard, code word or nominal area, strand count, съпротива, rated strength, total length and drum schedule. AAC is bare conductor; it does not include insulation or a steel-reinforcement core.

AAC Conductor Construction

A typical AAC design uses hard-drawn 1350-H19 aluminum wires arranged in concentric layers. ASTM B230 covers the aluminum wire, while ASTM B231 covers concentric-lay-stranded AAC. IEC 61089 provides another specification framework for round-wire concentric-lay overhead conductors. A project specification must identify the governing edition and any utility-specific requirements.

Close view of the all-aluminum stranded construction of AAC conductor
All-aluminum strands provide high conductivity, while mechanical loading remains a line-design consideration.
Construction itemTypical AAC arrangementЗащо има значение
Материал на проводникаAluminum 1350-H19 under common ASTM designsDefines conductivity and wire mechanical properties
StrandingConcentric layers, commonly 7, 19, 37 or more wires depending on sizeControls finished diameter, flexibility and mechanical behavior
CoreNo steel or alloy-reinforcement coreDistinguishes AAC from ACSR and ACAR
ИзолацияNoneLine clearances and insulation coordination belong to the overhead system
SurfaceBare metallic finishWire damage, sharp edges and surface defects require inspection

Where AAC Fits in an Overhead Line

AAC is commonly considered for short-span distribution, substation connections and other overhead circuits where conductivity and low conductor mass are useful and the required tensile performance is moderate. It is not automatically the correct choice for long crossings, high wind or ice loading, large ruling spans, or routes that demand a reinforced core.

Bare aluminum conductors installed on an overhead distribution line
AAC can suit short-span overhead circuits when the line design permits its mechanical characteristics.

The line engineer determines suitability from the conductor tension limit, support spacing, sag-temperature behavior, wind and ice cases, clearance requirements, fittings and local loading rules. An attractive resistance value does not compensate for inadequate mechanical performance.

Electrical and Mechanical Data Must Be Read Together

The following values are reference examples derived from a published ASTM B231 manufacturer table. They illustrate the relationship between size, диаметър, маса, resistance and rated strength; they are not an XWA guaranteed datasheet. Final values must come from the approved technical schedule and referenced standard.

Code wordSizeStrandingПрибл. диаметърПрибл. масаDC resistance at 20°CRated strength
Rose4 AWG7 жици5.89 мм58 кг/км1.358 Ω/км3.92 kN
Iris2 AWG7 жици7.42 мм92 кг/км0.853 Ω/км6.00 kN
Poppy1/0 AWG7 жици9.35 мм147 кг/км0.538 Ω/км8.85 kN
Aster2/0 AWG7 жици10.52 мм186 кг/км0.427 Ω/км11.16 kN
Phlox3/0 AWG7 жици11.79 мм234 кг/км0.338 Ω/км13.52 kN

Ampacity is deliberately excluded from this reference table. Current-carrying capacity changes with ambient temperature, solar radiation, wind speed and direction, conductor temperature and surface condition. IEC TR 61597 describes calculation considerations for overhead conductors; a single ampacity figure without its environmental assumptions is incomplete.

AAC, AAAC and ACSR Are Not Interchangeable

ДиригентCore constructionRelative design emphasisTypical selection boundary
AACAll aluminumConductivity and low massShorter spans and moderate mechanical duty
AAAC драйверAll aluminum alloyHigher strength and corrosion performance than AACRoutes needing an alloy conductor without steel reinforcement
ACSR проводникAluminum strands over steel coreHigh tensile capabilityLonger spans or greater mechanical loading

This comparison is directional, not a substitution rule. Conductor area, material grade, stranding and loading assumptions must be compared on the same basis. The aluminum conductor range provides the broader product-family context.

Manufacturing and Inspection Controls

Concentric stranding equipment used in bare aluminum conductor production
Stranding control covers wire condition, lay direction, lay length and finished conductor surface.

AAC quality depends on both the incoming aluminum wire and the completed strand. Inspection normally confirms wire diameter and condition, strand count, lay direction and lay length, overall diameter, conductor mass, DC resistance and mechanical values required by the purchase specification. Test scope must be agreed against the applicable standard; a standard reference alone is not evidence of third-party certification.

  • Confirm the exact standard, edition, code word or nominal cross-sectional area.
  • Define stranding, conductor class and required dimensional tolerances.
  • State resistance and rated-strength requirements using the same unit system as the standard.
  • Include routine tests, inspection hold points and required document format in the technical schedule.
  • Coordinate conductor data with fittings, clamps and stringing equipment before production release.

Drum Packing and Identification

Wooden drums prepared for overhead aluminum conductor packing
Дължина на барабана, gross weight and identification should follow the approved packing schedule.

Drum planning is part of the technical delivery. Required cut lengths should follow the line stringing plan so that avoidable joints are not introduced. Drum flange diameter, barrel diameter, gross weight and lifting arrangement must remain compatible with transport and site handling limits.

Typical drum identification includes product description, стандартен, conductor size or code word, strand count, net length, net and gross mass, drum number, production reference and direction of rolling. Exact markings follow the contract and destination requirements.

Standards and Engineering References

IEC 61089 defines electrical and mechanical characteristics for covered conductor families, while ASTM B230 and ASTM B231 are common references for 1350-H19 wire and completed AAC. Официалният IEC 61089 publication page is linked for scope verification. The standard named in a quotation must match the requested conductor system; mixing IEC and ASTM code words or tables without a declared basis can create dimensional and acceptance conflicts.

AAC Conductor FAQ

Is AAC conductor insulated?

не. AAC is normally a bare overhead conductor. ABC cable is an insulated aerial bundled product and should not be specified as AAC.

Does AAC conductor have a voltage rating?

AAC itself is not selected by a fixed cable voltage rating. System voltage, conductor clearances, insulators and insulation coordination are determined by the complete overhead line design.

When is AAAC or ACSR more suitable?

AAAC or ACSR may be more suitable when the route requires greater tensile strength, longer spans, or a different balance of sag, corrosion resistance and conductivity. See the engineering comparison of ACSR and AAAC conductor selection.

What information defines an AAC conductor quotation?

A usable configuration identifies the standard and edition, code word or conductor area, strand count, required length, drum schedule, resistance and rated-strength limits, test documentation, marking and destination handling constraints.

Contact XWA for AAC Conductor

XWA prepares the conductor construction and technical schedule around the applicable standard, code word or nominal area, stranding, required length and inspection documents.

Материал: Aluminum 1350-H19

Строителство: Bare concentric-stranded conductor

Стандарти: ASTM B231 / IEC 61089 project specifications

    Получете безплатна оферта 24 часове

    Имейл*:

    Име*:

    Вашата страна:

    Тел*:

    Вашите изисквания*: